FlightGlobal.com
Home
Premium
Archive
Video
Images
Forum
Atlas
Blogs
Jobs
Shop
RSS
Email Newsletters
You are in:
Home
Aviation History
1923
1923 - 0672.PDF
NOVEMBER 1, 1923 NEW AMERICAN NIGHT FLYING MAIL 'PLANES A LITTLE while back the U.S. Air Mail Service issued tendersfor a certain number of aeroplanes designed specially to meet the various requirements for night mail service. As a resultthree types of machines have already materialised, one from each of three well-known American aircraft constructors—the Aeromarine Plane and Motor Co., of Keyport, N.J., the Curtiss Aeroplane and Motor Co., of Garden City, N.Y., andthe Glenn L. Martin Co., of Cleveland. We give below brief descriptions of these three machines, together with illustrations.It may be mentioned that these machines are intended for use on the "night section " of the New York-San Franciscoair mail service, that is, the section between Chicago and Cheyenne. The Aeromarine Night Mail 'Plane.—The machine designedand built by the Aeromarine Co. is a two-bay tractor biplane increase the flow of air through the lower part of the core,and to reduce interference to air flow of plane at this. part. The radiator is provided with shutters.It will be noticed that the top plane is of larger span and chord than the lower one, the two planes being staggeredso that the rear struts are perpendicular to the chord. This arrangement of wings is claimed to be particularly advan-tageous when good load-carrying capacity and climb are required. It also allows better field of view for the pilot.The lower wings only are given a dihedral angle. Aeromarine No. 2A wing curve is used on both planes.This curve is an improvement of No. 2, originally designed for use on Air Mail 'plane type WM (converted DH4) whichwas described in FLIGHT for November 16, 1922. This curvenot only gives a low landing speed (45 m.p.h.), but enable& HEB BHEHS m Side and front views of the Aero- marine Night Mail 'Plane, 400 h.p. Liberty engine. • H H H m E 13 a .ft m MHMHHHHH' with metal fuselage, and fitted with a high compression 400h.p. Liberty engine. The fuselage is kept very narrow in order to decreaseresistance and improve the pilot's vision, and tapers consider- ably towards the rear. It is of plate girder (semi-monocoque)construction, built up entirely of duralumin (17/S/alloy) sheet. The covering is 3^-in. thick,»the bulkheads vary from3^-in. to T^-in., and the longerons, of angle section, are -j^-in. thick. Heavy reinforcements of -j^-in. duralumin are intro-duced at points where openings occur, such as the pilot's cockpit, mail compartment, etc. The engine is completelyand very neatly cowled in, ample ventilation being provided. The engine mounting is made up of steel tubing and woodenbearers. It is an easy matter to remove the cowling, which is in four parts, each secured by long hinge pins, and whenremoved, the engine is left exposed on all sides, allowing all repairs to be made with great facility. Ample clearance isleft between the engine and the fuselage proper, thus providing easy access to distributor heads, generator, water pump,petrol strainers and engine controls. The oil tank is located under the engine, and acts at thesame time as oil radiator—the cooling being regulated by opening or shutting doors in the lower cowl. The engineradiator is mounted on the top plane at the leading edge, and is supported by two brackets. It is easily removed byundoing three nuts and two water connections. Sufficient clearance is left between the radiator and the plane in order to loads to be carried far in excess of the ordinary if requiredin emergency. Furthermore, being comparatively thick, deep and strong wing spars are used. These are of heavyI-section spruce with built-up spruce ribs. A feature of the wing constuction is that the centre lines of front and rearspars are in line with the centre lines of the struts. This enables very simple and effective strut fittings being used, andeliminates offset bending movements in any direction. The wing bracing is of the two-bay type, the top planes beingattached to a central cabane over the fuselage. The inter- plane struts are of Navy No. 1 section, which together withstreamline bracing wires give very small parasite resistance. Large aile/ons are fitted to both top and bottom planes,and the upper ailerons are balanced by means of small balancing panels.Two petrol tanks, of 50 gal. capacity each are mounted on the top plane, giving a gravity feed with 3 to 4 ft. head.These tanks are of welded aluminium alloy sheet bairel construction, and are streamlined by metal and fabric fairing.The tail surfaces are also constructed of 17 S.^lloy, and can be removed from the fuselage as a unit. The horizontalstabiliser is adjustable from the pilot's cockpit. The landing gear is of the conventional V type, with acomparatively wide track—7 ft. 6 ins.—so that the wheels and shock absorber units are entirely out of the slipstream. The principal characteristics of this machine are:—•Span, 50 ft. (top), 45 ft. (bottom) ; chord, 7 ft. (top), 5 it 672
Sign up to
Flight Digital Magazine
Flight Print Magazine
Airline Business Magazine
E-newsletters
RSS
Events
