FlightGlobal.com
Home
Premium
Archive
Video
Images
Forum
Atlas
Blogs
Jobs
Shop
RSS
Email Newsletters
You are in:
Home
Aviation History
1924
1924 - 0610.PDF
SEPTEMBER 25, 1924 transmitted evenly to front and rear spar and extra stiffness added to the structure. The lift wires, which like the anti- lift wires are in duplicate but placed in close proximity to one another, are attached at their lower end to the fuselage at a point between the spars, and this point of the inner rib is also anchored to the fuselage, so that this rib is supported in three instead of two places. The peculiar bracing arrange ment, while making folding a little more difficult on account of the extra supporting wire needed in the folded condition, should save a fair amount of head resistance. It may be recollected that on a small Avro biplane with back-swept wings, flown by Raynham in 1914, a similar system of bracing was adopted, and the form is one which would appear to have certain advantages, although at first sight it looks somewhat startling. Certainly it reduces to a minimum the exposed portions of the biplane bracing, and except for going into cantilever wings it would be difficult to imagine a " cleaner " biplane. The top centre-section has tubular spars and struts but ordinary wood ribs. In order to give access to the front cockpit the strutting of the centre-section is somewhat unusual. The spars are supported on two vees, one on each side, while the front spar is laterally braced by tubes converging on the centre-line of the fuselage, ahead of the front cockpit. The ailrons run the whole length of the wings, and have a large diameter Duralumin leading edge forming a torque tube operated by cranks at the inner end. Variable flap gear is provided, the rear end of the longitudinal rocking shaft being raised and lowered by a worm. This worm gear is very beautifully carried out, and is illustrated by sketches. It will be seen that as the shaft is raised, the cranks are raised with it and the flaps depressed. The differential action is still retained. Only the bottom plane flaps are directly operated, the top flaps being connected to them by struts near the inner end. The wings are arranged for folding, the hinge pin being moved into a steel bracket off-set from the centre-line of the spar when the wings are folded. When spreading the wings this bolt is withdrawn and put into the hole on the centre-line. The fuselage is of similar construction to last year's Avro machines—i.e., square-section longerons with Warren girder strut bracing, secured by three-ply gussets or " biscuits " as they are sometimes called. This form of construction seems to be becoming popular for light 'planes, and it certainly avoids the necessity of trueing-up after hard use. The fuselage is fabric covered, except for the deck fairing, which has a three-ply covering underneath the fabric. Controls are of usual type, with wood " joy-sticks," but the foot bars are rather ingeniously arranged to give a parallel movement. In a narrow fuselage it is difficult to provide against the pilot's foot slipping, owing to the great angle of a short foot bar. In the Avro " Avis '" a parallel link motion is imparted to the front foot bar, which is somewhat shorter than the rear one, and the pilot's feet do not rest on the bar itself but on stirrups which always remain at right angles to the centre line of the fuselage. THE AVRO " AVIS " : View of the engine mounting, undercarriage, etc. An oleo undercarriage with very long travel is employed, the front chassis struts acting as radius rods for the axle. In proportion to the wing span the wheel track is fairly wide, and with the good shock absorbing properties of the oleo gear the machine should handle well on the ground and should stand up to some fairly rough landings such as it might receive in school work and, incidentally, in the low-speed tests at Lympne. Lateral bracing is between front struts only. The Avro " Avis " will be piloted in the competitions by Hinkler, and in view of the clean design and the wing flap gear the speed range should be considerable. The workman ship is very fine, and especially so that put into the variable camber gear, which as a matter of fact looks almost too good and perfect for a school machine. THE AVRO "AVIS," BLACKBURNE RADIAL ENGINE: Side view. 610
Sign up to
Flight Digital Magazine
Flight Print Magazine
Airline Business Magazine
E-newsletters
RSS
Events
